Two AC inputs with integrated transfer switch :
The Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source.
Two AC Outputs :
The main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.

• 5-year warranty

Pylon battery cable accessory kit for use with the US2000B, US2000B Plus and Phantom-S models. Each battery unit includes the interlink battery cables for parallel connection to another battery, whereas this pack is for connecting to the charger.
You require one cable pack per system, with a maximum of 5 batteries. With a system of more than 5 batteries, an additional cable pack would be required.
This cable pack includes the following cables:
2 x 2m long power cables (positive and negative)
1 x 3.5m RJ45 Communication cable (Not for CAN communication)

A set of battery brackets that allows vertical stacking of the Pylon battery unit. 1 set is required per additional battery added.

550W is the latest in JA Solar's 72-cell range. This module with its 11-bus-bar half-cell configuration can reach a peak power output of 550W. This module offers better temperature-dependent performance and enhanced tolerance for mechanical loading.

Package Consists of :

• Variosole Mounting Rail 41 x 35 x 3300mm
• End Clamp 30 – 50mm Silver
• Middle Clamp 31 – 51mm Silver
• Roof Hook /Anchor bolt/Seam Clamp
• Variosole Rail Connectors for rail 41 x 35 mm

The kit comes with the right amount of each component to adhere to Sans regulations. Some roofs use more components than others, due to size, shading, rafters, and other factors seen during installation. As this is part of a full turn-key solution, we supply, enough to get the job done regardless of the changeable factors

The MPPT RS SmartSolar is a 48V Solar charge controller with up to 450VDC PV input and either 100A, or 200A output. It is used in on-grid and off-grid solar applications where maximum battery charging power is required.

Product Features:

• Multiple MPPT Tracking inputs
• Isolated PV connections for additional safety
• 80 to 450 VDC input range with 120VDC start-up voltage
• Display and Bluetooth
• VE CAN and VE direct port
• Configure and monitor with Victron Connect APP
• 30 Day history on individual MPPT
• 2 x MPPT

The Cerbo GX provides intuitive control and monitoring. It has the same functionality as the Colour Control GX, with a few extras: - lower cost, mainly because it has no display or buttons

Product Features

• 4 resistive tank level inputs
• 4 temperature inputs
• 4 digital inputs
• WiFi & Bluetooth to Victron Connect App
• HDMI & USB to connect touch 50 or other display
• Ethernet port
• 3 x USB ports
• Micro SD card
• 2 x relay outputs
• BMS Can
• VE Can
• Ve Bus
• 3  x VE Direct ports

Panels and system monitoring.

The GX Touch 50 and GX Touch 70 are display accessories for our Cerbo GX. The five inch and seven inch touch screen displays give an instant overview of your system and allow to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, Their super slim waterproof design, top-mountable setup and simple installation bring a lot of flexibility when creating a crisp and clean dashboard.

The anti-islanding box is a complete pre-wired and easy to install an anti-islanding device consisting of a Ziehl anti-islanding relay
(model UFR1001E or model SPI1021), the required circuit breakers and a 63A contactor.

Ziehl UFR1001E:
Certificates: G83/2 and G59/3 (UK),
Fulfills the requirements of NRS-097-2-1 (South Africa).

Ziehl SPI1021:
Certificate: CEI 0-21 (Italy).

The Lynx Distribution System is a modular busbar system that incorporates DC connections, distribution, fusing, battery monitoring and/or Lithium battery management   Product Features:

• Lynx Power In - A positive and negative busbar with 4 connections for batteries or DC equipment.
•  Lynx Distributor - A positive and negative busbar with 4 fused connections for batteries or DC equipment together with fuse monitoring.
•  Lynx Shunt VE.Can - A positive busbar with a space for a main system fuse and a negative busbar with a shunt for battery monitoring. It has VE.Can communication for monitoring and setup with a GX device
• . Lynx Smart BMS - For use together with Victron Energy Smart Lithium batteries. It contains a positive busbar with a contactor that is driven by a battery management system (BMS) and a negative busbar with a shunt for battery monitoring. It has Bluetooth communication for monitoring and setup via the VictronConnect App and VE.Can communication for monitoring with a GX device and the VRM portal.

A modular DC bus bar

Product Features

•  with locations for four DC fuses
•  It will monitor the status of each fuse, and indicate its condition with a LED on the front.
•  Part of the modular Lynx distribution system.

The Lynx Distributor ships together with a 40cm RJ10 cable. This cable provides power to the Lynx Distributor and if connected to a Lynx Smart BMS, is also used to transmit data.

Fuses to be purchased separately

The Victron fuse range is an easy DC protection and specially designed for all DC protection

• Protective fuse cover
• Approx volts drop is specified for every fuse
• fuses have the volts and current specified
• cold resistance specified on the datasheet for every fuse
• 3 ranges are MIDI; MEGA and ANL (described on the datasheet)

The kit is consists of:

• 16mm square copper earth cable
• 4mm square earth cable for bonding
• Copper coated Lightning Rod

This kit works in conjunction with our DC-Combiner box that has Type II DC Surge Arresters installed

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

When any work is done that changes the Ac cabling a COC is issued and when there are panels involved a DC annexure is issued that supplements the COC

Electrical Installation.

This is the wiring of the electrical part of your system, inverters, change-over switches, additional AC boxes, DC boxes and includes the supply of AC cabling. This also includes all bonding and fitment of necessary earth spike/s or additional surge protection and wiring thereof. Also splitting of your DB BOX to comply with SA Regulations. Testing and compliancy is also done during this part of the installation.